Raymarine EV-400 Evolution Autopilots

The Raymarine EV-400 line of autopilots are engineered for simplicity, Evolution autopilots eliminate the need for complicated set up and calibration. Once Raymarine EV-400 autopilot is installed, getting started is as easy as switching the autopilot on.

Raymarine EV-400 Power Evolution Autopilot

*Requires Type 2 or Type 3 Hydraulic Pump

Features:

• Heavy-duty, 30 Amp output for Type 3 Drives or Constant Running Pumps
  
• Evolution Ai for superior performance
  
• NO calibration required
  
• SeaTalk^ng Network Compatible
  
• ACU-400 auxiliary power to SeaTalk^ng network
  
• Includes p70R Autopilot Controller

Includes:

• EV-1 Sensor Core
  
• p70RS Autopilot Control Head
  
• ACU-400 Actuator Control Unit (Includes the M81105 Rotary Rudder Reference)
  
• Evolution Cabling Kit
  
• EV Unit O-Ring Pack (set of 2)
  
• Wall Mounting Bracket

EV-400 Sail Evolution Autopilot

*Requires Type 2 or Type 3 Drive Unit

Features:

• Heavy-duty, 30 Amp output for Type 3 Drives or ZF Sail Pod Drive Systems
  
• Evolution Ai for superior performance
  
• No calibration required
  
• SeaTalk^ng Network Compatible
  
• ACU-400 auxiliary power to SeaTalk^ng network
  
• Includes p70 Autopilot Controller

Includes:

• EV-1 Sensor Core
  
• p70S Autopilot Control Head
  
• ACU-400 Actuator Control Unit (Includes the M81105 Rotary Rudder Reference)
  
• Evolution Cabling Kit
  
• EV Unit O-Ring Pack (set of 2)
  
• Wall Mounting Bracket

The EV Sensor Core
At the center of every Evolution system is the intelligent EV sensor core, a 9-axis sensor that monitors vessel motion in all three dimensions. The innovative EV sensor core combines advanced solid-state sensors with the Evolution autopilot processor into a single easy-toinstall housing.

Mount the EV sensor core above or below decks, the rugged enclosure is fully sealed and built to IPX6 and IPX7 waterproofing and submersion standards.

The EV-1 is designed for Evolution mechanical and hydraulic autopilot systems. SeaTalk^ng networking enables a single cable connection for power and data to the Evolution ACU (actuator control unit) and extended SeaTalk^ng and NMEA2000 networks.

Features:

• Precision monitoring of heading, pitch, roll, and yaw allowing the autopilot to evolve instantly as sea conditions and vessel dynamics change
  
• Flexible installation options
  
• Mount above or below deck
  
• Simple SeaTalk^ng connectivity to the control head and ACU
  
• Solid state sensor technology delivers dynamic accuracy to within 2 degrees in all conditions
  
• Fast and reliable heading data for MARPA, radar overlay, and heading modes on Raymarine multifunction displays

p70R Autopilot Control Head
The p70R has a convenient rotary control knob and support for multiple autopilot modes including Auto, standby, trolling patterns, and track mode from your GPS or chartplotter.

Features:

• LightHouse user interface is simple and quick to use
  
• Wide 160° viewing angles
  
• Start up wizard helps you configure the pilot quickly and easily
  
• Anti-reflective coating for improved visibility in bright sunlight
  
• Low power - typically 132mA/1.6W - 27% less than ST70 at x4 measured brightness
  
• Supported autopilot modes: Auto; Standby; Pattern; Track; Wind Vane; Power Steer and Jog Steer
  
• Simple system and group dimming/illumination
  
• Support for multiple data sources
  
• SeaTalk^ng/NMEA2000 and SeaTalk1 connectivity (no bridging required)

ACU-400 Autopilot Control Unit (ACU)
The rugged ACU (Actuator Control Unit) delivers reliable autopilot drive power and also provides power to the SeaTalk^ng bus. Choose the ACU that fits your steering system type.

Support Drive Units
Heavy-duty, 30 Amp output for Type 3 Drives or Constant Running Pumps

Evolution Cabling Kit

• 1 x SeaTalk^ng Power Cable (0.4m)
  
• 1 x SeaTalk^ng Backbone Cable (5m)
  
• 1 x SeaTalk^ng Spur Cable (0.4m)
  
• 1 x SeaTalk^ng 5-way Connector Block
  
• 2 x SeaTalk^ng T-piece Connector
  
• 2 x SeaTalk^ng Terminator